Every repair starts with what is actually wrong
Whatever the asset is doing, there is a named service for it here: repair, protection, refurbishment, testing, recertification. Every one of them starts with finding the actual problem.
What is failing?
-
A valve or choke that will not hold
-
A wellhead, tree or BOP due for service
-
A pump losing performance
-
Flow iron or drilling iron due for test or recertification
- Flow-iron pressure-testing Hydrostatic testing of flow iron and pressure equipment in Trinidad, each item proven against its rating with a written record.
- DME iron recertification Recertification of drilling and measurement equipment iron in Trinidad: a real examination against service history, then the certificate.
-
Corroded or eroded steel, tanks and pipework
- Belzona application In-place application of Belzona polymeric and composite systems by SUAC's in-house Specialist: metal rebuilt cold, protected, and back in service.
- In-place repair & protective coatings Engineered linings and coatings applied on site, with the chemistry matched to the service conditions, to extend asset life without an outage.
- Splash-zone composite reinforcement Cold-bonded plate and ASME PCC-2-qualified composite encapsulation for casings and conductors in the splash zone. No hot work, no well re-entry.
-
A hydraulic cylinder that leaks or drifts
-
Chemical dosing that drifts
Repair & Protection
Engineered non-weld polymeric and composite repair, protection and maintenance. Restore corroded and worn equipment in place, with no hot work.
-
Belzona application
Damaged metal rebuilt to working tolerances in place, often inside a single shutdown or tidal window, with no hot work.
View service -
Splash-zone composite reinforcement
Splash-zone casings, conductors, and structures reinforced and sealed in place, with no hot work and no well re-entry.
View service -
In-place repair & protective coatings
Protection applied before failure, in place, so the asset keeps working and the capital spend stays deferred.
View service
Equipment Services
Recertification, refurbishment, and service for pressure and production equipment, handled in-country. Extend asset life without replacement.
-
DME iron recertification
Iron recertified on a proper examination, in days and in-country, so the certificate means what it claims.
View service -
Wellhead, Christmas-tree & BOP service
Pressure-control equipment back on the well with its seal and rating restored, on an in-country turnaround.
View service -
Valve refurbishment
A valve that holds seal and pressure again, with a test record to show it, instead of an unexamined replacement.
View service -
Flow-iron pressure-testing
Iron proven against its rating before it goes on the job, with a test record per item.
View service -
Pump service
A pump back on its curve through in-country rebuild with genuine parts, instead of a replacement order and its lead time.
View service -
Automated chemical-injection
Dosing held at the rate the duty needs, without the drift and the crew time of manual injection.
View service -
Hydraulic-cylinder repair
Cylinders rebuilt to specification locally, with a test record, instead of waiting out an overseas repair loop.
View service
One sequence, on every job
The same five steps for every asset. The first three are the evaluation, and stopping after them is a legitimate outcome.
-
Evaluate
The asset is assessed where it stands, or stripped and inspected at our facility.
-
Report
You get the findings in writing: condition, cause where the evidence supports it, and our recommendation.
-
Decide
The decision is yours, made on evidence rather than a guess.
-
Execute
The scoped work proceeds in-country, by the team that did the inspection.
-
Return to service
The equipment goes back into service, and we stand behind the work.
A structural repair in the splash zone, with no hot work and no well re-entry
For an independent, Trinidad-focused operator, we reinforced a splash-zone conductor with composite encapsulation. Structural integrity restored in place, with no hot work and no well re-entry. ASME PCC-2-qualified Belzona materials applied by our in-house Specialist.
Read the workStart with the diagnosis, not the guess
Send us the scope, the equipment, or the problem. We evaluate it at no charge and with no obligation, and the answer comes back in writing.