Skip to content
Part of the Damus Group of Companies
An engineer inspecting a wellhead valve assembly
Technical Evaluation

Know what the asset needs before you spend on it

A choke that will not hold, a valve that leaks after every service, a pump losing head: the expensive mistake is deciding repair or replace without knowing what is actually wrong. Send it to us. Our engineers strip it, inspect it, and put the answer in writing.

What you get

The report is the product

Every evaluation ends in a written technical report on the asset’s actual condition. It is an engineering document you can hand to your own team, and it is yours whether or not any work follows.

  1. Condition findings

    What a disassembly-level inspection found: wear, corrosion, damage, and the state of every critical component, documented as we saw it.

  2. Cause, where the evidence shows it

    What failed and why, where a strip-down supports a determination. We report what we found, not what we guess.

  3. A recommendation with reasons

    Repair or replace, argued on the merits of the asset in front of us. The recommendation is ours; the decision stays yours.

  4. The scope to follow

    If you proceed, the report becomes the scope of work, with the cost following from what the inspection found.

If the report says leave the asset alone, that is the answer you get.

Whoever made it

We evaluate and repair any maker’s equipment.

SUAC represents twelve engineered product lines, and that agency work is where the depth comes from: factory relationships, genuine parts access, and engineers who strip and rebuild these assemblies in-country. Representation never limits what comes through the door. If the asset matters to your operation, we will look at it, whoever built it.

Parts access informs the recommendation. It never decides it.
Before you send it

What to send us

  • The asset and what it does.
  • The maker and model, if you know them.
  • What it is doing wrong.
  • The service conditions.
  • Photographs and the nameplate, if you have them.
  • How urgent it is.

The asset comes to our workshop in Point Fortin, or we collect it.

How it runs

One sequence, start to finish

The same five steps for every asset, from a single valve to a skid. The first three are the evaluation, and stopping after them is a legitimate outcome: you keep the report.

  1. Evaluate

    The asset is assessed where it stands, or stripped and inspected at our facility.

  2. Report

    You get the findings in writing: condition, cause where the evidence supports it, and our recommendation.

  3. Decide

    The decision is yours, made on evidence rather than a guess.

  4. Execute

    The scoped work proceeds in-country, by the team that did the inspection.

  5. Return to service

    The equipment goes back into service, and we stand behind the work.

A technician in a yellow hard hat working at the flange of a red blowout preventer
Why it works

Built so the honest answer wins

The evaluation is structured so the recommendation you get is the one the evidence supports.

  • Evidence before money

    A repair-or-replace call made without a strip-down is a guess. The evaluation replaces the guess with a disassembly-level inspection, so whatever you spend next is spent on evidence.

  • We earn either answer

    SUAC repairs equipment and supplies it. If repair is the right call, we do the work. If replacement is, we supply the unit. The recommendation does not have to steer you, because either answer is work we can stand behind.

  • The report stands on its own

    It is written to be forwarded: to your engineers, your manager, or procurement. With no obligation attached, the argument inside it has to stand on the evidence alone.

Before you decide

Common questions

Is there a charge?
The evaluation is at no charge. If you proceed, the report becomes the scope of work, with the cost following from what the inspection found.
What if we do not proceed?
Stopping after the report is a legitimate outcome: you keep the report.
Does it have to be equipment you supplied?
No. We evaluate and repair any maker’s equipment. If the asset matters to your operation, we will look at it, whoever built it.
Where is it done?
The asset comes to our workshop in Point Fortin, or we collect it. We strip it down and inspect every critical component.
What happens next

Tell us what the asset is doing

Tell us the asset, the symptom, and the urgency. Whatever the report finds, the decision stays with you.